|
طب جانباز، جلد ۸، شماره ۲، صفحات ۱۱۹-۱۲۵
|
|
|
عنوان فارسی |
تاثیر سوکت لبهسیلیکونیِ پروتز ترنسفمورال بر میزان فشار در نواحی تحمل وزن فوقانی و مقایسه با سوکت مرسوم |
|
چکیده فارسی مقاله |
اهداف: پس از قطع عضو و دریافت پروتز، فشارهای بیش از حد بین استامپ و سوکت از مهمترین مشکلات افراد استفادهکننده از پروتز است. هدف این مطالعه، طراحی و ساخت سوکت با لبه سیلیکونی در پروتز ترنسفمورال و بررسی میزان فشار در نواحی تحمل وزن فوقانی در مقایسه با سوکت مرسوم بود. بیمار و روشها: در این مطالعه موردی تکنمونهای، یک مرد 38ساله با قطع عضو ترنسفمورال تروماتیک سمت راست مورد بررسی قرار گرفت. برای این فرد دو عدد سوکت، یکی بهروش مرسوم و دیگری با لبه سیلیکونی ساخته شد. برای اندازهگیری فشارها با استفاده از FSR (مقاومت حساس به نیرو) و برد میکروکنترلری آردوئینو دستگاه اندازهگیری فشار ساخته شد. یافتهها: در سنسور زیر راموس تحتانی پوبیس (شماره 8) در حالت ایستاده روی دو پا 9/24% و در حالت ایستاده روی پای پروتزی 8/50% افزایش فشار در سوکت دارای لبه سیلیکونی نسبت به سوکت مرسوم مشاهده شد. در سنسور بالای مثلث اسکارپا (شماره 2) در حالت ایستاده روی پای پروتزی 1/29% و در سنسور روی سکوی ایسکیال (شماره 7) در حالت راهرفتن در زمان پاسخ بارگذاری 4/2% افزایش فشار در سوکت دارای لبه سیلیکونی مشاهده شد. در همه حالتها و در هر دو سوکت، کمترین فشار در سنسور تروکانتر بزرگ فمور (شماره 4) بود. در مابقی نقاط در همه حالتها، فشار در سوکت دارای لبه سیلیکونی از سوکت مرسوم کمتر بود. نتیجهگیری: استفاده از سوکت با لبه سیلیکونی در پروتز ترنسفمورال در مقایسه با سوکت مرسوم باعث کاهش فشارهای وارده به استامپ میشود. |
|
کلیدواژههای فارسی مقاله |
پروتز ترنسفمورال، سوکت لبه سیلیکونی، فشار، تحمل وزن |
|
عنوان انگلیسی |
Effect of Silicone Brim Socket of Transfemoral Prosthesis on Pressure Level in Proximal Weight Bearing Areas and Comparing with Conventional Socket |
|
چکیده انگلیسی مقاله |
Aims: High pressures between the stamp and the socket after mutilation and receiving a prosthetic device is one of the main problems of the persons using such prosthesis. The aim of this study was to design and make a socket with a silicone brim in the trans-femoral prosthesis, as well as to investigate the pressure in the upper weight bearing areas compared to the current socket. Patient & Methods: In the one-sample case study, a 38-year-old male person with unilateral (right side) traumatic trans-femoral amputation was studied. Two sockets, one made by the current method and another made with a silicone brim, were presented to the person. Using FSR (force sensing resistance) and an Arduino Due microcontroller board, a pressure measurement device was used to measure the pressure level. Findings: In the sensor under the inferior pubic ramus (No. 8), there were 24.9% and 50.8% pressure increases in the silicone brim socket than the current socket in bipedal standing and standing on the prosthetic leg, respectively. In the sensor located in the upper part of scarpa's triangle (No. 2), there was 29.1% pressure increasing on the silicone brim socket standing on the prosthetic leg. In addition, in the sensor on the ischial pad (No. 7), there was 2.4% pressure increasing on the silicone brim socket during walking at the loading response. The lowest pressure was in the femur great trochanter sensor (No. 4) in all cases and both sockets. On other points in all studied conditions, there were lower pressure levels in the silicone brim socket than the current socket. Conclusion: Using the silicone brim socket in the trans-femoral prosthesis leads to decreasing of the pressures on the stamp compared to the current sockets. |
|
کلیدواژههای انگلیسی مقاله |
|
|
نویسندگان مقاله |
حبیب اجرایی دولت آباد | ejraei dolat abad h orthotics amp; prosthetics department, school of rehabilitation, madad karan street, shah nazari street, mother square, tehran, iran تهران، خیابان میرداماد، میدان مادر، خیابان شهید شاه نظری، خیابان مددکاران، دانشکده توانبخشی، گروه ارتوز و پروتز
بهنام حاجی آقایی | haji aghaei b orthotics amp; prosthetics department, rehabilitation faculty, iran university of medical sciences, tehran, iran گروه آموزشی ارتوز و پروتز، دانشکده توانبخشی، دانشگاه علوم پزشکی ایران، تهران، ایران سازمان اصلی تایید شده: دانشگاه علوم پزشکی ایران (Iran university of medical sciences)
مریم جلالی | jalali m orthotics amp; prosthetics department, rehabilitation faculty, iran university of medical sciences, tehran, iran گروه آموزشی ارتوز و پروتز، دانشکده توانبخشی، دانشگاه علوم پزشکی ایران، تهران، ایران سازمان اصلی تایید شده: دانشگاه علوم پزشکی ایران (Iran university of medical sciences)
حسن سعیدی | saeedi h orthotics amp; prosthetics department, rehabilitation faculty, iran university of medical sciences, tehran, iran گروه آموزشی ارتوز و پروتز، دانشکده توانبخشی، دانشگاه علوم پزشکی ایران، تهران، ایران سازمان اصلی تایید شده: دانشگاه علوم پزشکی ایران (Iran university of medical sciences)
|
|
نشانی اینترنتی |
http://www.ijwph.ir/browse.php?a_code=A-10-1302-1&slc_lang=fa&sid=fa |
فایل مقاله |
اشکال در دسترسی به فایل - ./files/site1/rds_journals/82/article-82-41219.pdf |
کد مقاله (doi) |
|
زبان مقاله منتشر شده |
fa |
موضوعات مقاله منتشر شده |
|
نوع مقاله منتشر شده |
1 |
|
|
برگشت به:
صفحه اول پایگاه |
نسخه مرتبط |
نشریه مرتبط |
فهرست نشریات
|