مجله علمی-پژوهشی علوم و فناوری جوشکاری ایران، جلد ۷، شماره ۲، صفحات ۳۹-۴۶

عنوان فارسی جوشکاری آلیاژهای پایه تیتانیومی توسط فرایند قوسی پالسی تنگستن-گاز و بررسی اثر فرکانس بر ریزساختار و خواص مکانیکی
چکیده فارسی مقاله دراین تحقیق ورق آلیاژی Ti-6Al-4V  با ضخامت یک میلی متر با طرح اتصال لب به لب توسط فرآیند جوشکاری قوس تنگستن-گاز با بهره­گیری از جریان پالسی (PCGTAW)  و با استفاده از فلز پرکننده AMS 4954G جوشکاری شد. در این پژوهش، بررسی اثر فرکانس سیستم پالس بر ریزساختار و خواص مکانیکی با استفاده از میکروسکوپ نوری و آزمونهای سختی سنجی ویکرز و کشش انجام گرفت. در نمونه جوش بدون فرکانس بدلیل عدم استفاده از جریان پالس و نرخ سرد شدن کمتر حوضچه مذاب، تشکیل مقادیر زیادی فازهای نرم لایه­ای ویدمن اشتاتن در منطقه فلز جوش میسر می­گردد. در نهایت در این روش کمترین میانگین سختی برابر 341  ویکرز حاصل شد. نتایج آزمایش­ها نشان داد که بکارگیری جریان پالسی و افزایش فرکانس پالس تا 450 هرتز باعث افزایش نرخ سرد شدن حوضچه مذاب و به دنبال آن افزایش مقدار فاز مارتنزیتیα' بصورت سبدی شکل در ناحیه فلزجوش و در نهایت افزایش میانگین ریزسختی در این ناحیه می­گردد. به بیان دیگر استفاده از بیشینه فرکانس منجر به افزایش قابل توجه میزان سختی تا 367 ویکرز  در ناحیه فلزجوش شد. در نهایت نیز با استفاده از آزمون کشش نشان داده شد که در همه نمونه­ها شکست از ناحیه فلز پایه رخ داده که این پدیده به دلیل کیفیت جوش بسیار مناسب نمونه ها بوده است.
کلیدواژه‌های فارسی مقاله آلیاژ Ti6Al4V، جوشکاری قوس تنگستن- گاز (GTAW)، فرکانس، سیستم جریان پالسی

عنوان انگلیسی Welding of titanium base alloys by tungsten-gas pulse arc process (PCGTAW) and investigation of frequency effect on microstructure and mechanical properties
چکیده انگلیسی مقاله In this research, Ti-6Al-4V alloy sheet with a thickness of one millimeter with butt joint design was welded by tungsten-gas arc welding process using pulse current (PCGTAW) and using AMS 4954G filler metal. In this study, the effect of pulse system frequency on microstructure and mechanical properties was investigated by optical microscopy, Vickers hardness and tensile strength tests. In the non-frequency welding sample, due to the lack of pulse current and lower cooling rate of the molten pool, the formation of large amounts of soft phases of the Weidmann-Statten layer in the weld metal region is possible. Finally, in this method, the lowest average hardness of 341 Vickers was obtained. The experimental results showed that using pulsed current and increasing the pulse frequency up to 450 Hz increased the cooling rate of the molten pool, followed by increasing the amount of martensitic phase α 'in the form of a basket in the weld metal region and finally increasing the average microhardness in this region. In other words, using the maximum frequency led to a significant increase in hardness up to 367 Vickers in the weld zone. Finally, using the tensile strength test, it was shown that in all the samples, failure occurred from the base metal area, which was a very good phenomenon due to the proper welding quality of the samples.
کلیدواژه‌های انگلیسی مقاله Ti6Al4V alloy, Tungsten-gas arc welding (GTAW), Frequency, Pulse current system

نویسندگان مقاله سید مهدی رفیعائی | Seyed Mahdi Rafiaei
گروه مهندسی مواد، دانشکده فنی مهندسی گلپایگان، دانشگاه صنعتی اصفهان، گلپایگان.

غلامحسین اسلامی | Gholamhosein Eslami
گروه مهندسی مواد، دانشکده فنی مهندسی گلپایگان، دانشگاه صنعتی اصفهان، گلپایگان.


نشانی اینترنتی http://jwsti.iut.ac.ir/browse.php?a_code=A-10-373-2&slc_lang=fa&sid=1
فایل مقاله فایلی برای مقاله ذخیره نشده است
کد مقاله (doi)
زبان مقاله منتشر شده fa
موضوعات مقاله منتشر شده تخصصی
نوع مقاله منتشر شده پژوهشی
برگشت به: صفحه اول پایگاه   |   نسخه مرتبط   |   نشریه مرتبط   |   فهرست نشریات