این سایت در حال حاضر پشتیبانی نمی شود و امکان دارد داده های نشریات بروز نباشند
صفحه اصلی
درباره پایگاه
فهرست سامانه ها
الزامات سامانه ها
فهرست سازمانی
تماس با ما
JCR 2016
جستجوی مقالات
چهارشنبه 17 دی 1404
Journal of Dentistry, Shiraz University of Medical Sciences
، جلد ۱۴، شماره ۴، صفحات ۱۹۱-۰
عنوان فارسی
چکیده فارسی مقاله
کلیدواژههای فارسی مقاله
عنوان انگلیسی
A Comparison between Shear Bond Strength of VMK Master Porcelain with Three Base-metal Alloys (Ni-cr-T3, VeraBond, Super Cast) and One Noble Alloy (X-33) in Metal-ceramic Restorations
چکیده انگلیسی مقاله
Statement of Problem: The increase in the use of metal-ceramic restorations and a high prevalence of porcelain chipping entails introducing an alloy which is more compatible with porcelain and causes a stronger bond between the two. This study is to compare shear bond strength of three base-metal alloys and one noble alloy with the commonly used VMK Master Porcelain. Materials and Method: Three different groups of base-metal alloys (Ni-cr-T3, Super Cast, and VeraBond) and one group of noble alloy (X-33) were selected. Each group consisted of 15 alloy samples. All groups went through the casting process and change from wax pattern into metal disks. The VMK Master Porcelain was then fired on each group. All the specimens were put in the UTM; a shear force was loaded until a fracture occurred and the fracture force was consequently recorded. The data were analyzed by SPSS Version 16 and One-Way ANOVA was run to compare the shear strength between the groups. Furthermore, the groups were compared two-by-two by adopting Tukey test. Results: The findings of this study revealed shear bond strength of Ni-Cr-T3 alloy was higher than the three other alloys (94 MPa or 330 N). Super Cast alloy had the second greatest shear bond strength (80. 87Mpa or 283.87 N). Both VeraBond (69.66 MPa or 245 N) and x-33 alloys (66.53 MPa or 234 N) took the third place. Conclusion: Ni-Cr-T3 with VMK Master Porcelain has the greatest shear bond strength. Therefore, employment of this low-cost alloy is recommended in metal-ceramic restorations.
کلیدواژههای انگلیسی مقاله
نویسندگان مقاله
احمدی زاده | a ahmadzadeh
dept. of prosthodontics, school of dentistry, ahwaz university of medical sciences, ahwaz, iran
a نشاطی | a neshati
resident of prosthodontics, school of dentistry, ahwaz university of medical sciences, ahwaz, iran
n موسوی | n mousavi
resident of prosthodontics, school of dentistry, ahwaz university of medical sciences, ahwaz, iran
s ایپک چی | s epakchi
resident of prosthodontics, school of dentistry, ahwaz university of medical sciences, ahwaz, iran
f دباغی تبریز | f dabaghi tabriz
resident of operative dentistry, school of dentistry, ahwaz university of medical sciences, ahwaz, iran
ah سربازی | ah sarbazi
prosthodontic specialist
نشانی اینترنتی
http://dentjods.sums.ac.ir/index.php/JDSUMS/article/view/259
فایل مقاله
فایلی برای مقاله ذخیره نشده است
کد مقاله (doi)
زبان مقاله منتشر شده
en
موضوعات مقاله منتشر شده
نوع مقاله منتشر شده
Original Article
برگشت به:
صفحه اول پایگاه
|
نسخه مرتبط
|
نشریه مرتبط
|
فهرست نشریات