|
|
International Journal of Engineering، جلد ۳۴، شماره ۵، صفحات ۱۳۵۲-۱۳۶۱
|
|
|
| عنوان فارسی |
|
|
| چکیده فارسی مقاله |
|
|
| کلیدواژه‌های فارسی مقاله |
|
|
| عنوان انگلیسی |
Influence of Immersion Corrosion on Mechanical Properties of AISI 430/AISI 316L Dissimilar Welded Joints |
|
| چکیده انگلیسی مقاله |
Dissimilar welded joints of AISI 430 and AISI 316L stainless steel were produced by the GMAW process using two different shielding gas mixtures composed of 97Ar-3N2 and 80Ar-19He-1O2. The microstructure of the heat-affected zone w:as char:acterized by optical and scanning electron microscopy, and Vickers microhardness measurements were carried out along the cross-section of the specimens. The dissimilar welded joints were submitted to immersion corrosion test in a 10%v/v hydrochloric acid solution for 24 and 72 hours. Afterward, yields strength, tensile strength, and elongation percentage were measured using tensile tests according to ASTM E8 standard. Non-immersed welded joints were used for comparison purposes. An analysis of variance was developed to evaluate the influence of immersion time and shielding gas mixture on yielding strength and tensile strength. The microstructure characterization showed that the heat-affected zone on AISI 430 side was the widest, and it was observed a significant presence of acicular ferrite, martensite, and coarsened ferritic grains. In contrast, on the heat-affected zone on AISI 316L side was not observed coarsening nor refinement of austenite grains. The AISI 430 heat-affected zone showed the maximum hardness values and higher susceptibility to corrosion damage. Tensile tests results evidenced that immersion corrosion tests did not change significantly ultimate strength in comparison to non-immersed specimens while yielding strength and elongation percentage were drastically decreased due to immersion time. According to the p-value, the immersion time is the most influencing factor on yielding strength and tensile strength of the dissimilar welded joints. |
|
| کلیدواژه‌های انگلیسی مقاله |
Dissimilar Weldedjoints,Stainless steel,corrosion,Tensile test,Heat-affected zone |
|
| نویسندگان مقاله |
A. M. Barrios |
Department of Mechanical Engineering, ICT research group, Universidad de Córdoba, Montería, Colombia
L. M. Burgos |
Department of Mechanical Engineering, ICT research group, Universidad de Córdoba, Montería, Colombia
E. E. Niebles-Nuñez |
Mechanical Engineering Program, IMTEF research group, Universidad Autónoma del Caribe, Barranquilla, Colombia
L. A. Espitia |
Department of Mechanical Engineering, ICT research group, Universidad de Córdoba, Montería, Colombia
J. Unfried-Silgado |
Department of Mechanical Engineering, ICT research group, Universidad de Córdoba, Montería, Colombia
|
|
| نشانی اینترنتی |
https://www.ije.ir/article_129366_d485c189cc9e056e35357a9f9816cfb9.pdf |
| فایل مقاله |
فایلی برای مقاله ذخیره نشده است |
| کد مقاله (doi) |
|
| زبان مقاله منتشر شده |
en |
| موضوعات مقاله منتشر شده |
|
| نوع مقاله منتشر شده |
|
|
|
|
برگشت به:
صفحه اول پایگاه |
نسخه مرتبط |
نشریه مرتبط |
فهرست نشریات
|